Free written estimates in Chicago and the near suburbs

Chicago Tuckpointing Co.Tuckpointing · Chimneys · Brick

DIY tuckpointing vs hiring a mason: an honest guide

DIY tuckpointing vs hiring a mason comes down to height, scale and the brick. A handful of failed joints at eye level on a garage or a newer house is a reasonable weekend job if you rake the joints deep enough and use a soft mortar. Whole walls, anything above a short ladder, chimneys, soft pre-war brick and work on a Chicago building that needs a licensed mason are jobs to hire out. Here's how to tell.

DIY4 min readUpdated November 20, 2026

Key takeaways
  • Small, low, accessible patches on sound brick are fair DIY.
  • The most common DIY failure is shallow joints filled with hard mortar.
  • Silica dust from grinding is a real health hazard; use dust control and a respirator.
  • In Chicago, masonry on buildings must be done by a licensed mason contractor.

DIY or hire? A quick decision table

Reasonable DIY

  • A few square feet of joints within reach from the ground
  • Garden walls, garage walls, planters
  • Newer, harder brick
  • Patience to rake joints deep by hand

Hire a mason

  • Anything above a short ladder
  • Chimneys and parapets
  • Soft pre-war common brick or landmark buildings
  • Loose brick, lintel cracks, bulging walls
  • Whole walls, or work on a Chicago building

How to do a small repair properly

  1. Rake out the joint to about 2 to 2½ times its width, usually 5/8" to 3/4", with a plugging chisel or a joint raker. Don't stop at the loose surface.
  2. Brush and dampen the joint. Dry brick sucks water from fresh mortar and ruins the bond.
  3. Use a soft mix. A bagged Type N is fine on newer brick. On old soft brick, use Type O or a lime mortar. See our mortar guide.
  4. Pack in layers about 1/4" deep with a tuckpointing trowel, letting each firm up before the next.
  5. Tool the joint when it's thumbprint-hard, to match the existing profile.
  6. Keep it damp and out of hot sun for a couple of days; don't work below about 40°F.
Hands working mortar on a wall with two trowels
Packing mortar with a narrow tuckpointing trowel, in thin layers, is the part DIYers most often rush.

Dust and safety

Mortar and brick contain crystalline silica. Grinding them makes fine dust that can cause serious lung disease. OSHA's silica standard for construction requires tuckpointing grinders to use a shroud connected to a dust-collecting vacuum, plus respiratory protection depending on the task. Homeowners aren't covered by OSHA, but the hazard is the same. For a small job, hand tools make far less dust. If you do use a grinder, use a shrouded one with a HEPA vacuum and wear a properly fitted respirator.

Ladders are the other risk. A pump jack, scaffold or lift is the safe way to work above a short ladder, and it's the main thing you're paying a mason for on taller walls.

DIY mistakes we end up fixing

  • Mortar smeared over shallow joints, which pops out after one winter
  • Grey Type S or cement patch on soft salmon brick, followed by spalling
  • Caulk or sealant in the joints, which traps water and has to be ground out
  • Mortar smeared across brick faces and left to harden
  • Patching lintel cracks instead of replacing the steel
Local specifics

The City of Chicago's masonry permit terms say that brick, stone, terra cotta and concrete building elements may only be installed or repaired by a Chicago-licensed mason contractor. That's a real limit on DIY masonry for Chicago buildings. Check with the Department of Buildings before you start. Suburbs have their own rules. See our permit guide.

So when is hiring worth it?

When the work is high, extensive, structural or on old soft brick, a mason's equipment and experience usually cost less than doing it twice. Try the estimator to see what a professional job would run, and compare it with the tools, mortar, rental equipment and weekends it would take you.

The tools a small DIY repair needs

ToolWhat it's for
Plugging chisel and hammer, or a joint rakerRemoving old mortar by hand without nicking brick edges
Tuckpointing trowel (joint width) and a hawkHolding mortar and packing it into the joint
Jointer matching your joint profileTooling the finished joint
Stiff brush and spray bottleCleaning out joints and dampening brick
Safety glasses, gloves, respiratorMortar is caustic and dust contains silica

A small hand-tool job makes little dust and is the safest way for a homeowner to start. If a joint won't come out by hand, it may be harder than the brick, and grinding it is where DIY repairs go wrong.

Quick answers

Can I use an angle grinder with a regular blade?A diamond tuckpointing blade with a dust shroud and vacuum, yes. Without dust control, no.
What about mortar repair caulk in a tube?Fine for a hairline gap in a garden wall. Not a substitute for repointing a building.
How much can I save doing it myself?On a small low patch, most of the cost. On anything needing scaffold, much less than you'd think.

See also: how we tuckpoint and the mortar checker.

Free estimate

Let us look at the wall before you pay for the whole thing

Three details and we'll call to set a time. We look at the joints, the bricks, the lintels and the chimney, then send a written price.

Rather talk it through? Call us.

We call back within one business day to set up a look at the wall. We use your details only to answer you, and we never sell them.

Call us