Chicago Tuckpointing Co.
Chicago tuckpointing for the brick this city was built from
Chicago tuckpointing is our main trade: we grind out worn mortar joints and refill them with mortar matched to your brick, on bungalows, two-flats, greystones and courtyard buildings across the city and near suburbs. We also rebuild chimneys, replace rusted steel lintels and repair parapets, and we'll tell you honestly when a wall only needs spot work.
- Written estimate with the square footage, mortar type and access spelled out
- Mortar matched to soft Chicago common brick, not hard cement that cracks it
- Express permits handled when the city requires one
Get a free estimate
Tell us about the wall. We'll call to set up a look.
- Joints raked deepOld mortar removed to 2–2½× the joint width, not smeared over
- Mortar matchedColor, strength and joint profile chosen for your brick
- Dust controlledShrouded grinders on vacuums, per OSHA's silica rule
- Price in writingSquare footage, access and extras listed line by line
What we do
Masonry services for Chicago buildings
Most calls start with "the mortar is falling out," and most end there too. When the wall needs more, it's usually one of these. Each page explains what the job involves, what it costs and when you don't need it. Or see the full list of masonry services.
Tuckpointing & repointing
Grinding out failed joints and repacking them in layers. Spot work or a full elevation, with mortar matched in color and hardness.
How we tuckpointChimney repair & rebuilds
Repointing, new crowns and caps, and rebuilding leaning stacks above the roofline, the part that takes the worst of the weather.
Chimney workBrick repair & replacement
Cutting out spalled, cracked and loose brick and toothing in salvaged or matched brick so the patch disappears.
Brick repairSteel lintel replacement
Rusting angle irons over windows lift and crack the brick above them. We take out the brick, replace the steel and relay it.
LintelsParapet & coping repair
The short walls around flat roofs on two-flats and storefronts: rebuilt, re-capped and flashed so water stops getting behind them.
ParapetsGreystone & masonry restoration
Limestone fronts, terra cotta trim and landmark facades: gentle cleaning, stone patching and repointing that passes landmark review.
RestorationChicago buildings
The four buildings we work on most
Chicago housing is mostly brick, and each common type wears out in its own predictable places. Knowing where to look is half the estimate.
Bungalows
Face brick on the front, softer common brick down the sides and back. The side walls, the chimney and the front steps usually go first. Our bungalow guide walks through it.
Two-flats & three-flats
Tall side walls a few feet from the neighbor, flat roofs with parapets, and steel lintels over every window. Access drives the price here.
Greystones
Indiana limestone fronts on brick buildings. The stone needs a softer, finer mortar and careful patching, never a grinder taken to carved trim.
Courtyard & walk-up buildings
Big 1910s–1920s apartment buildings with parapets, terra cotta and long runs of lintels. Usually phased over several seasons.
Why mortar fails here
Chicago winters are hard on mortar joints
Water soaks into the joints, freezes, expands and pushes the mortar apart a little more each time. Chicago goes through dozens of freeze-thaw swings in a typical winter, and spring rain refills every crack before the next one. The sides of the building that face the lake or the west and north winds wear fastest. Chimneys and parapets, exposed on every side, go first of all.
Mortar is meant to be the sacrificial part of the wall. When it's softer than the brick, it wears out and gets replaced every few decades while the brick lasts a century. Trouble starts when someone repoints old soft brick with a hard, cement-rich mix: the brick becomes the weak link, and the faces start popping off in sheets. We see that every week, often on walls redone within the last 20 years.
So the first thing we do on any wall is look at what's there: the brick, the original mortar, and what the last mason used. Then we pick the mortar. Our mortar guide for old Chicago brick explains Type N, Type O and lime mixes, and our mortar checker helps you judge your own wall.
By building age
What to expect from your building, decade by decade
When a Chicago building went up tells us a lot before we even get out of the truck: what the brick is, what the original mortar was, and what has probably failed already. This is the rough guide we work from.
| Built | Typical building | Brick and mortar | What usually needs work now |
|---|---|---|---|
| Before 1900 | Workers' cottages, early two-flats, rowhouses in Pilsen, Bridgeport, Wicker Park | Soft common brick, lime mortar | Full repoint in lime or Type O mortar; earlier cement patches to remove; often landmark review |
| 1890s–1920s | Greystones, two- and three-flats, courtyard buildings | Limestone fronts, common brick sides, lime-rich mortar | Parapets, lintels, stone joints, side walls |
| 1910–1940 | Bungalows, Georgians, Tudors | Face brick front, common brick sides, cement-lime mortar | Chimney, front steps, weather-side wall, side window lintels |
| 1945–1970 | Brick ranches, raised ranches, Georgians, walk-ups | Harder face brick all round, Type N-style mortar | Chimney crowns, steps, planter boxes, first lintels |
| 1970 onward | Townhomes, newer infill, brick veneer | Brick veneer over framing, modern mortar | Usually just flashing, sills and weep holes; full repoints rare |
Veneer walls on newer buildings behave differently from the solid brick walls of older Chicago buildings: there's an air gap and flashing behind the brick, and leaks are usually flashing problems, not mortar problems. We'll tell you which kind of wall you have on the first visit.
Check your own wall
Does your brick need tuckpointing yet?
Walk around the building and tick what you see. It won't replace a look from a mason, but it'll tell you whether this is a this-year job or a keep-an-eye-on-it job. The full checker has photos and more signs.
How it works
What happens from first call to final cleanup
We look at the wall
Usually within a week. We check joint depth, scratch-test the mortar, look at lintels, the chimney and the parapet, and note what the last repair used.
Written price
Square footage per elevation, spot or full repoint, mortar type, access method, brick and lintel counts, and whether a permit applies.
Permit & scheduling
For Chicago jobs we file the Express Permit when one's needed. Landmark buildings get a mortar sample for review first.
Grind out
Joints are cut to 2–2½ times their width with shrouded grinders on HEPA vacuums. Windows, plants and AC units get covered.
Repoint & tool
Mortar goes in in layers, each one firm before the next, then tooled to match your joint profile: concave, flush, raked or struck.
Clean & walk-through
Mortar smears brushed off, the alley and gangway swept, and we walk the wall with you before we call it done.
A real schedule
What a full repoint looks like, day by day
People ask how long we'll be at their house and what it will be like living there while we work. Here's a typical full repoint of a two-flat side wall from scaffold, about 1,400 square feet of brick:
| Day | What happens | What you'll notice |
|---|---|---|
| 1 | Scaffold goes up in the gangway; windows, AC units and the neighbor's wall get covered | Truck in the alley, noise from setup, plastic on your windows |
| 2–4 | Grinding out the joints, top to bottom, with vacuums running | The loudest days. Keep windows on that side closed |
| 4–5 | Loose or spalled bricks cut out and replaced; joints blown clean | Quieter; bricks being chiseled |
| 5–8 | Repointing in layers from the top down, tooling as each section firms up | Very little noise; the wall changes color as joints fill |
| 9 | Brushing off, final touch-ups, scaffold down, gangway and alley cleaned | Walk-through with us before we leave |
Rain days, very hot afternoons and cold mornings stretch that out; we don't repoint in weather that will hurt the mortar. A bungalow side wall from ladders and pump jacks typically takes three to five working days. Spot tuckpointing is often a single day.
Price ranges
What Chicago masonry repairs usually cost
Ballpark ranges for typical Chicago jobs. Height and access move the number more than anything else: the same wall costs noticeably more on a third floor than at eye level. The tuckpointing cost guide breaks it down and has an estimator.
Spot tuckpointing
$800–$2,500
Worst joints on one or two walls of a bungalow, from ladders.
Full repoint, per sq ft
$10–$18
Ground-reachable wall. Add 20–45% for tall ladders or scaffold.
Chimney rebuild
$3,800–$8,500
Above the roofline, with a new crown. Repointing only: $900–$2,200.
Lintel replacement
$1,100–$2,400
Per window opening up to 6 ft, including relaying the brick above.
When to book
Chicago's masonry season, month by month
Mortar has to stay above roughly 40°F while it cures, and it shouldn't bake in direct summer sun either. That gives Chicago a long but finite season. Spring books up fast because everyone notices the damage after winter. Our post on the best time of year for tuckpointing goes deeper.
IdealWorkable with careHeated enclosure only
September and October are our favorite months: mild, dry and steady. In July and August we start early, mist the joints and shade the wall so the mortar doesn't dry before it sets.
Straight answers
When you shouldn't hire us (or anyone) yet
A good part of our job is telling people what can wait. These come up all the time.
A few hairline cracks
Fine cracks in joints on a sheltered wall are normal. Mark them with a pencil and the date and look again next spring.
"Seal the whole house"
Sealers don't fix bad joints, and the wrong film-forming sealer traps water in soft brick. Repoint first; seal only exposed walls, with a breathable product.
Small DIY patches
A handful of joints at eye level on a garage is a fair weekend job if you rake them out deep enough. We wrote up when DIY makes sense.
Permits & rules
Chicago permits, licensing and landmark review
In Chicago, tuckpointing and routine masonry repair are covered by the Department of Buildings' Express Permit Program, and the work has to be done by a Chicago-licensed mason contractor. Rebuilding a whole multi-wythe wall needs a plan-reviewed permit instead. If your building is a designated landmark or sits in a landmark district like Wicker Park, Old Town Triangle or the Logan Square Boulevards, the Commission on Chicago Landmarks' staff reviews the work and typically asks for mortar that matches the original in color, texture and joint profile.
The suburbs run their own permit offices. Oak Park and Evanston also have preservation commissions that review work in their historic districts. Our Chicago tuckpointing permit guide covers all of it, including what to ask any contractor before they start.
Read the permit guideWhere we work
Chicago neighborhoods and nearby suburbs
We work across the city, from the bungalow belt on the Northwest and Southwest Sides to the two-flats of Logan Square, Avondale and Pilsen, and in the brick-heavy inner-ring suburbs. See all areas we cover.
Field Notes
Guides for Chicago building owners
How we work on your block
Good neighbors on narrow Chicago lots
Masonry work in Chicago happens a few feet from someone else's house. Gangways are tight, alleys are shared, and grinding dust travels. Here's what we do on every job, not just the big ones:
- Knock on the neighbors' doors before we grind a gangway or party wall
- Shrouded grinders on HEPA vacuums, not open grinding
- Plastic over windows, AC units, plants and cars nearby
- Sound old brick salvaged and reused, not dumped
- Alley and gangway swept and cleared at the end of every day
- Scaffold permits for the public way when we're over a sidewalk
Want to know more about who we are and how we price? Read about our crew, or see the full list of masonry services.
Chicago tuckpointing questions
How much does tuckpointing cost in Chicago?
Most Chicago homeowners pay $10 to $18 per square foot for a full grind-and-repoint on a wall reachable from the ground, and more when scaffolding is needed. Spot tuckpointing on a bungalow often runs $800 to $2,500. Our cost page has an estimator.
Do I need a permit for tuckpointing in Chicago?
Usually yes. The City of Chicago treats tuckpointing as masonry repair and covers it through the Express Permit Program, and the work must be done by a Chicago-licensed mason contractor. Landmark buildings also need Historic Preservation review. Details are in our permit guide.
How often does brick need tuckpointing?
Good mortar lasts roughly 25 to 30 years on a sheltered wall, less on chimneys, parapets and walls facing the lake or the prevailing west and north winds. Most Chicago homes need spot work every 8 to 15 years. More in how often brick needs tuckpointing.
When is tuckpointing season in Chicago?
Roughly April through November. Mortar needs temperatures above about 40°F while it cures, so winter work needs heated enclosures and costs more.
Should old Chicago brick be repointed with Type S mortar?
Usually not. Pre-war Chicago common brick is soft, and hard portland-heavy mortar makes the brick faces pop off. We match the mortar to the brick, often Type N or Type O, or a lime mortar on the oldest buildings.
What's the difference between tuckpointing and repointing?
Strictly, repointing means replacing mortar in the joints, and tuckpointing is a decorative technique using two mortar colors with a thin raised line. In Chicago, everyone says "tuckpointing" for both, and so do we.
Can you match my mortar color?
Usually closely. We mix test batches with different sands and pigments, let them dry (wet mortar looks darker) and compare them on the wall before starting. On a full elevation, small differences disappear; on spot repairs they can show for a year or two until the new mortar weathers.
Is the grinding dusty?
Grinding mortar makes silica dust, which is why OSHA's silica rule requires shrouded grinders on dust-collecting vacuums for this work. We use them, cover windows and AC units, and tell neighbors on gangway walls before we start.
Do you rebuild chimneys or just repoint them?
Both. A chimney with sound brick and worn joints gets repointed and a new crown. One that's leaning, cracked through or losing brick gets taken down to solid masonry, usually at or just below the roofline, and rebuilt. See chimney repair.
Do you work in winter?
Small urgent repairs, yes, under heated enclosures. For a full repoint we'd rather book you for April: winter enclosures add cost and the results are less forgiving.
Free estimate
Get a straight answer about your wall
Name, phone and where the building is. We'll set a time to look and send a written estimate, whether it's spot work or a full repoint.
Rather talk it through? Call us.