Chimney repair in Chicago
Chimney repair in Chicago is the most common call we get after general tuckpointing, because the chimney is the most exposed brick on the house. We repoint stacks with sound brick, replace cracked crowns, and rebuild leaning or crumbling chimneys from solid masonry up. If you don't use the chimney anymore, we'll also tell you when taking it down is the smarter money.
A chimney takes wind, rain and freeze-thaw on all four sides, and on many Chicago houses it also carries warm, damp exhaust from a gas furnace or water heater up the middle. That combination wears joints from outside and inside at once. It's why a chimney can look rough while the walls below it are fine.
Signs your chimney needs work
- Mortar missing from joints, especially on the side facing west or north
- Bricks cracked, spalled (faces popped off) or loose near the top
- Pieces of brick or mortar on the roof, in the gutter or in the gangway
- A visible lean, or a gap opening where the chimney meets the roof
- A cracked or crumbling crown, the concrete or mortar cap on top
- White staining (efflorescence) on the chimney or on the inside wall next to it
- Water stains on the ceiling or wall beside the chimney after rain
Repoint, re-crown or rebuild?
| What we find | What we recommend | Typical cost |
|---|---|---|
| Worn joints, brick sound, chimney plumb | Grind and repoint the stack above the roof | $900–$2,200 |
| Crown cracked, rest okay | New crown with an overhang and drip edge, plus a cap | $550–$1,400 |
| Top courses loose, rest sound | Partial rebuild of the top 2–4 feet, new crown | $1,800–$4,000 |
| Leaning, cracked through, lots of spalled brick | Rebuild from the roofline (or below) with new crown | $3,800–$8,500 |
| Not used by any appliance | Consider removing below the roofline and patching the roof | Often less than a rebuild |
How a chimney rebuild goes
- Access and protection. Roof jacks, planks or a lift, depending on pitch and height. Tarps over the roof and gutters to catch debris.
- Take down to solid brick. We remove brick course by course until the mortar under it is sound. That's often at the roofline, sometimes a few courses below.
- Flue. Existing clay flue tile is checked as it's exposed. If the chimney serves a furnace or water heater, the liner needs to suit that appliance. We'll recommend a chimney sweep or HVAC contractor inspect it, since that's their specialty, not ours.
- Rebuild. New or salvaged brick to match, laid in mortar suited to the exposure, with the original corbel detail if there was one.
- Crown and flashing. A properly formed crown with an overhang, then new counterflashing cut into the joints where the chimney meets the roof (or coordinated with your roofer).
- Cleanup. Roof, gutters and the ground below cleared of brick and mortar.
Crowns, caps and flashing
Most leaky chimneys we see have a crown problem, not a brick problem. Many original crowns are just a sloped smear of mortar, called a "wash", that cracks within a few winters and lets water straight down into the brick. A proper crown is thicker, overhangs the brick by 1 to 2 inches with a drip groove underneath, and is separated from the flue tile so they can move independently.
A cap (the metal hood over the flue) keeps rain, birds and squirrels out. Flashing is the metal at the roof line. Leaks there are often blamed on the brick but are really flashing failures. When the roof is due soon, it's worth coordinating so the roofer and mason don't each pay to open the same area. Our post on why brick walls leak explains how to tell which part is at fault.
Many Chicago bungalows and two-flats have a chimney still venting a gas boiler or water heater, often through an old clay flue. Acidic condensation from modern appliances attacks mortar from the inside, so these chimneys can fail faster than ones that aren't used. Rebuilding chimney masonry in Chicago falls under masonry repair and needs a Chicago-licensed mason contractor; see our permits guide.
What if you don't use the chimney?
Lots of Chicago houses have a chimney that hasn't vented anything since the coal boiler was pulled. If a heating contractor confirms nothing vents into it, you have options: rebuild it to keep the look of the house (usually our advice on a front-facing chimney or in a historic district), or take it down below the roofline and have the roof patched over. Removal is often cheaper and ends the maintenance. Check with your local permit office or the landmarks staff first if the building is landmarked.
Chimney repair costs in Chicago
A chimney repoint usually runs $900 to $2,200; a new crown $550 to $1,400; a full rebuild above the roofline $3,800 to $8,500. Height, roof pitch, the number of flues and whether there's decorative corbelling drive the range. You can price a chimney along with the rest of the house in our estimator.
Chimney questions
How much does it cost to rebuild a chimney in Chicago?
Rebuilding a typical single-flue house chimney above the roofline usually costs $3,800 to $8,500 including a new crown, depending on height, roof pitch and access. Repointing a sound chimney is usually $900 to $2,200.
Can I remove a chimney I don't use?
Often, yes. If no appliance vents through it, taking the chimney down below the roofline and patching the roof can cost less than a rebuild. A heating contractor should confirm nothing still vents into it first.
Is chimney repair covered by homeowners insurance?
Wear and weathering usually isn't. Sudden damage, such as a lightning strike or a tree limb, sometimes is. Check your policy and call your insurer before work starts if you think it was sudden.
Related: the walls below the chimney often need tuckpointing too, and spalled brick is covered under brick repair. We rebuild chimneys across Chicago and in Skokie, Park Ridge and Berwyn.
More Field Notes
Free estimate
Chimney shedding brick?
Tell us where the house is and what you're seeing. We'll look at the stack, the crown and the flashing and give you the options in writing.
Rather talk it through? Call us.