Free written estimates in Chicago and the near suburbs

Chicago Tuckpointing Co.Tuckpointing · Chimneys · Brick

Why is my brick wall leaking? How to find the real source

If you're asking why your brick wall is leaking, the answer is usually above the stain, not at it. Water enters through open mortar joints, cracked chimney crowns, parapet coping, failed flashing at lintels and roofs, or a gutter overflowing down the wall, then travels down inside the masonry before it shows up indoors. Here's how to trace it before anyone starts grinding.

Troubleshooting4 min readUpdated November 20, 2026

Key takeaways
  • Water in solid brick walls moves down and sideways; the source is usually higher than the stain.
  • Chimneys, parapets, sills and gutters cause more leaks than flat wall areas.
  • Efflorescence (white salt) shows where water is moving through the wall.
  • Fix the source first; sealers rarely fix a leak.

Match where it shows up to where it comes from

Where you see waterLikely sources
Ceiling or wall beside the chimneyChimney crown, flashing, open joints on the stack
Top-floor ceilings along an outside wallParapet coping, roof-to-parapet flashing
Below windowsSills with open joints or no drip, failed lintel flashing above
Above windowsLintel with no flashing, open joints above the head
Basement wall, near a cornerDownspout discharge, grading, open joints near grade
Spread across a whole wall after stormsWidespread open joints on a weather-facing wall
Two brick chimneys on a rooftop under a cloudy sky
Chimneys collect water on all sides and from the top. A cracked crown can show up as a stain a whole floor below.

Reading efflorescence

Efflorescence is the white, powdery deposit on brick or on interior plaster. Water dissolves salts inside the masonry and leaves them behind as it evaporates at the surface. A little after a very wet spring is normal on new or newly repointed work. Heavy or recurring efflorescence in one area is a map of where water is moving through the wall. It usually sits just below the entry point: under a sill, below a chimney, at the top of a wall under a parapet.

Brush it off dry with a stiff brush. Don't wash it with lots of water, which just dissolves the salts back into the wall. Once the water source is fixed, it stops coming back.

How to trace a leak, step by step

  1. Note when it leaks: every rain, only wind-driven rain from one direction, or only during snowmelt.
  2. Look straight up from the stain on the outside: sill, lintel, gutter, chimney, parapet.
  3. Check the gutters in a rain: overflowing at a corner, a downspout that's lost its elbow, or water running behind the gutter.
  4. Get on the roof (or have someone do it): chimney crown, flashing, coping joints.
  5. Scratch-test the joints on that wall. Our mortar checker explains how.
  6. Water test if needed: run a hose on one area at a time, from the bottom up, while someone watches inside.
Local specifics

In Chicago, wind-driven rain from storms off the plains and off the lake soaks west- and north-facing walls and lake-side elevations far more than others. If your leak only shows up in storms from one direction, that wall's joints or its windows are the prime suspects. Two-flats and courtyard buildings with flat roofs often leak at the parapet. See parapet repair.

Fixes by source

  • Open joints: tuckpointing the affected wall.
  • Chimney crown or stack: new crown, repoint or rebuild. See chimney repair.
  • Parapet coping: reset with through-wall flashing.
  • Lintels and sills: replace rusted steel, add flashing, repoint sill joints. See lintels.
  • Gutters and downspouts: a gutter contractor, and the cheapest fix on the list.
  • Porous brick on an exposed wall: after the above, perhaps a breathable repellent. See waterproofing.

Solid brick vs brick veneer: why it matters for leaks

Most Chicago buildings from before about 1950 have solid masonry walls: two or three layers of brick tied together, with plaster applied right on the inside. Water that gets in has to soak through or dry back out, so leaks show up as damp plaster close to the source. Newer houses and additions usually have brick veneer: a single layer of brick with an air gap, a water-resistant barrier and flashing behind it, and small weep holes at the bottom. Veneer leaks almost always mean a flashing or weep problem, and repointing alone won't fix them. Knowing which wall you have changes where we look first.

Quick answers

Will sealing the brick stop the leak?Rarely on its own. Most leaks come through joints, flashing and tops of walls, not through sound brick.
Is efflorescence dangerous?No, but it's a sign of moving water, which over time can damage brick and plaster.
Should I fix the interior plaster first?No. Fix the source, let the wall dry, then repair the plaster.

Evanston or lakefront building? Our Evanston page covers lake-facing walls.

Free estimate

Let us look at the wall before you pay for the whole thing

Three details and we'll call to set a time. We look at the joints, the bricks, the lintels and the chimney, then send a written price.

Rather talk it through? Call us.

We call back within one business day to set up a look at the wall. We use your details only to answer you, and we never sell them.

Call us