Free written estimates in Chicago and the near suburbs

Chicago Tuckpointing Co.Tuckpointing · Chimneys · Brick
Red brick Chicago building with a white door and tall windows

Chicago Tuckpointing Co.

Chicago tuckpointing for the brick this city was built from

Chicago tuckpointing is our main trade: we grind out worn mortar joints and refill them with mortar matched to your brick, on bungalows, two-flats, greystones and courtyard buildings across the city and near suburbs. We also rebuild chimneys, replace rusted steel lintels and repair parapets, and we'll tell you honestly when a wall only needs spot work.

  • Written estimate with the square footage, mortar type and access spelled out
  • Mortar matched to soft Chicago common brick, not hard cement that cracks it
  • Express permits handled when the city requires one

Get a free estimate

Tell us about the wall. We'll call to set up a look.

We reply within one business day. Your details are only used to answer you.

  • Joints raked deepOld mortar removed to 2–2½× the joint width, not smeared over
  • Mortar matchedColor, strength and joint profile chosen for your brick
  • Dust controlledShrouded grinders on vacuums, per OSHA's silica rule
  • Price in writingSquare footage, access and extras listed line by line

Chicago buildings

The four buildings we work on most

Chicago housing is mostly brick, and each common type wears out in its own predictable places. Knowing where to look is half the estimate.

Row of brick houses with front porches on a tree-lined Chicago street

Bungalows

Face brick on the front, softer common brick down the sides and back. The side walls, the chimney and the front steps usually go first. Our bungalow guide walks through it.

Multi-story red brick building with rows of windows

Two-flats & three-flats

Tall side walls a few feet from the neighbor, flat roofs with parapets, and steel lintels over every window. Access drives the price here.

Stately brick and stone building with a black door and tall windows

Greystones

Indiana limestone fronts on brick buildings. The stone needs a softer, finer mortar and careful patching, never a grinder taken to carved trim.

Brick apartment building with a steel fire escape on its side wall

Courtyard & walk-up buildings

Big 1910s–1920s apartment buildings with parapets, terra cotta and long runs of lintels. Usually phased over several seasons.

Why mortar fails here

Chicago winters are hard on mortar joints

Water soaks into the joints, freezes, expands and pushes the mortar apart a little more each time. Chicago goes through dozens of freeze-thaw swings in a typical winter, and spring rain refills every crack before the next one. The sides of the building that face the lake or the west and north winds wear fastest. Chimneys and parapets, exposed on every side, go first of all.

Mortar is meant to be the sacrificial part of the wall. When it's softer than the brick, it wears out and gets replaced every few decades while the brick lasts a century. Trouble starts when someone repoints old soft brick with a hard, cement-rich mix: the brick becomes the weak link, and the faces start popping off in sheets. We see that every week, often on walls redone within the last 20 years.

So the first thing we do on any wall is look at what's there: the brick, the original mortar, and what the last mason used. Then we pick the mortar. Our mortar guide for old Chicago brick explains Type N, Type O and lime mixes, and our mortar checker helps you judge your own wall.

Cross-section of a mortar joint before and after tuckpointingLeft: an eroded joint with a crack and water entering. Right: the joint ground out to about two and a half times its width and repacked flush in layers. Before: worn jointAfter: raked and repacked Mortar recessed and cracked:water gets in, freezes, pushesthe joint and brick apart. raked ~5/8" to 1" deep New mortar packed in 1/4" layers,tooled to match the old profile,softer than the brick.
Why we grind out instead of smearing over: a skim coat on top of a soft, recessed joint pops off within a winter or two.

By building age

What to expect from your building, decade by decade

When a Chicago building went up tells us a lot before we even get out of the truck: what the brick is, what the original mortar was, and what has probably failed already. This is the rough guide we work from.

BuiltTypical buildingBrick and mortarWhat usually needs work now
Before 1900Workers' cottages, early two-flats, rowhouses in Pilsen, Bridgeport, Wicker ParkSoft common brick, lime mortarFull repoint in lime or Type O mortar; earlier cement patches to remove; often landmark review
1890s–1920sGreystones, two- and three-flats, courtyard buildingsLimestone fronts, common brick sides, lime-rich mortarParapets, lintels, stone joints, side walls
1910–1940Bungalows, Georgians, TudorsFace brick front, common brick sides, cement-lime mortarChimney, front steps, weather-side wall, side window lintels
1945–1970Brick ranches, raised ranches, Georgians, walk-upsHarder face brick all round, Type N-style mortarChimney crowns, steps, planter boxes, first lintels
1970 onwardTownhomes, newer infill, brick veneerBrick veneer over framing, modern mortarUsually just flashing, sills and weep holes; full repoints rare

Veneer walls on newer buildings behave differently from the solid brick walls of older Chicago buildings: there's an air gap and flashing behind the brick, and leaks are usually flashing problems, not mortar problems. We'll tell you which kind of wall you have on the first visit.

Check your own wall

Does your brick need tuckpointing yet?

Walk around the building and tick what you see. It won't replace a look from a mason, but it'll tell you whether this is a this-year job or a keep-an-eye-on-it job. The full checker has photos and more signs.

Quick mortar check

How it works

What happens from first call to final cleanup

  1. We look at the wall

    Usually within a week. We check joint depth, scratch-test the mortar, look at lintels, the chimney and the parapet, and note what the last repair used.

  2. Written price

    Square footage per elevation, spot or full repoint, mortar type, access method, brick and lintel counts, and whether a permit applies.

  3. Permit & scheduling

    For Chicago jobs we file the Express Permit when one's needed. Landmark buildings get a mortar sample for review first.

  4. Grind out

    Joints are cut to 2–2½ times their width with shrouded grinders on HEPA vacuums. Windows, plants and AC units get covered.

  5. Repoint & tool

    Mortar goes in in layers, each one firm before the next, then tooled to match your joint profile: concave, flush, raked or struck.

  6. Clean & walk-through

    Mortar smears brushed off, the alley and gangway swept, and we walk the wall with you before we call it done.

A real schedule

What a full repoint looks like, day by day

People ask how long we'll be at their house and what it will be like living there while we work. Here's a typical full repoint of a two-flat side wall from scaffold, about 1,400 square feet of brick:

DayWhat happensWhat you'll notice
1Scaffold goes up in the gangway; windows, AC units and the neighbor's wall get coveredTruck in the alley, noise from setup, plastic on your windows
2–4Grinding out the joints, top to bottom, with vacuums runningThe loudest days. Keep windows on that side closed
4–5Loose or spalled bricks cut out and replaced; joints blown cleanQuieter; bricks being chiseled
5–8Repointing in layers from the top down, tooling as each section firms upVery little noise; the wall changes color as joints fill
9Brushing off, final touch-ups, scaffold down, gangway and alley cleanedWalk-through with us before we leave

Rain days, very hot afternoons and cold mornings stretch that out; we don't repoint in weather that will hurt the mortar. A bungalow side wall from ladders and pump jacks typically takes three to five working days. Spot tuckpointing is often a single day.

Price ranges

What Chicago masonry repairs usually cost

Ballpark ranges for typical Chicago jobs. Height and access move the number more than anything else: the same wall costs noticeably more on a third floor than at eye level. The tuckpointing cost guide breaks it down and has an estimator.

Spot tuckpointing

$800–$2,500

Worst joints on one or two walls of a bungalow, from ladders.

Full repoint, per sq ft

$10–$18

Ground-reachable wall. Add 20–45% for tall ladders or scaffold.

Chimney rebuild

$3,800–$8,500

Above the roofline, with a new crown. Repointing only: $900–$2,200.

Lintel replacement

$1,100–$2,400

Per window opening up to 6 ft, including relaying the brick above.

Red brick house with snow on the ground and bare trees around it
Snow sitting against a brick wall all winter keeps the bottom courses wet. Those joints and the steps go first.

When to book

Chicago's masonry season, month by month

Mortar has to stay above roughly 40°F while it cures, and it shouldn't bake in direct summer sun either. That gives Chicago a long but finite season. Spring books up fast because everyone notices the damage after winter. Our post on the best time of year for tuckpointing goes deeper.

Janenclose
Febenclose
Marestimates
Aprstart
Maybusy
Jungood
Julhot
Aughot
Sepbest
Octbest
Novwatch temps
Decenclose

IdealWorkable with careHeated enclosure only

September and October are our favorite months: mild, dry and steady. In July and August we start early, mist the joints and shade the wall so the mortar doesn't dry before it sets.

Straight answers

When you shouldn't hire us (or anyone) yet

A good part of our job is telling people what can wait. These come up all the time.

A few hairline cracks

Fine cracks in joints on a sheltered wall are normal. Mark them with a pencil and the date and look again next spring.

"Seal the whole house"

Sealers don't fix bad joints, and the wrong film-forming sealer traps water in soft brick. Repoint first; seal only exposed walls, with a breathable product.

Small DIY patches

A handful of joints at eye level on a garage is a fair weekend job if you rake them out deep enough. We wrote up when DIY makes sense.

Permits & rules

Chicago permits, licensing and landmark review

In Chicago, tuckpointing and routine masonry repair are covered by the Department of Buildings' Express Permit Program, and the work has to be done by a Chicago-licensed mason contractor. Rebuilding a whole multi-wythe wall needs a plan-reviewed permit instead. If your building is a designated landmark or sits in a landmark district like Wicker Park, Old Town Triangle or the Logan Square Boulevards, the Commission on Chicago Landmarks' staff reviews the work and typically asks for mortar that matches the original in color, texture and joint profile.

The suburbs run their own permit offices. Oak Park and Evanston also have preservation commissions that review work in their historic districts. Our Chicago tuckpointing permit guide covers all of it, including what to ask any contractor before they start.

Read the permit guide
The limestone Chicago Water Tower on Michigan Avenue
The Chicago Water Tower, one of the few buildings to survive the 1871 fire, is Joliet limestone. Old stone like this needs soft, matched mortar.

How we work on your block

Good neighbors on narrow Chicago lots

Masonry work in Chicago happens a few feet from someone else's house. Gangways are tight, alleys are shared, and grinding dust travels. Here's what we do on every job, not just the big ones:

  • Knock on the neighbors' doors before we grind a gangway or party wall
  • Shrouded grinders on HEPA vacuums, not open grinding
  • Plastic over windows, AC units, plants and cars nearby
  • Sound old brick salvaged and reused, not dumped
  • Alley and gangway swept and cleared at the end of every day
  • Scaffold permits for the public way when we're over a sidewalk

Want to know more about who we are and how we price? Read about our crew, or see the full list of masonry services.

Narrow Chicago alley lined with brick buildings
Most of our work happens back here: alleys, gangways and side walls a few feet from the neighbors.

Chicago tuckpointing questions

How much does tuckpointing cost in Chicago?

Most Chicago homeowners pay $10 to $18 per square foot for a full grind-and-repoint on a wall reachable from the ground, and more when scaffolding is needed. Spot tuckpointing on a bungalow often runs $800 to $2,500. Our cost page has an estimator.

Do I need a permit for tuckpointing in Chicago?

Usually yes. The City of Chicago treats tuckpointing as masonry repair and covers it through the Express Permit Program, and the work must be done by a Chicago-licensed mason contractor. Landmark buildings also need Historic Preservation review. Details are in our permit guide.

How often does brick need tuckpointing?

Good mortar lasts roughly 25 to 30 years on a sheltered wall, less on chimneys, parapets and walls facing the lake or the prevailing west and north winds. Most Chicago homes need spot work every 8 to 15 years. More in how often brick needs tuckpointing.

When is tuckpointing season in Chicago?

Roughly April through November. Mortar needs temperatures above about 40°F while it cures, so winter work needs heated enclosures and costs more.

Should old Chicago brick be repointed with Type S mortar?

Usually not. Pre-war Chicago common brick is soft, and hard portland-heavy mortar makes the brick faces pop off. We match the mortar to the brick, often Type N or Type O, or a lime mortar on the oldest buildings.

What's the difference between tuckpointing and repointing?

Strictly, repointing means replacing mortar in the joints, and tuckpointing is a decorative technique using two mortar colors with a thin raised line. In Chicago, everyone says "tuckpointing" for both, and so do we.

Can you match my mortar color?

Usually closely. We mix test batches with different sands and pigments, let them dry (wet mortar looks darker) and compare them on the wall before starting. On a full elevation, small differences disappear; on spot repairs they can show for a year or two until the new mortar weathers.

Is the grinding dusty?

Grinding mortar makes silica dust, which is why OSHA's silica rule requires shrouded grinders on dust-collecting vacuums for this work. We use them, cover windows and AC units, and tell neighbors on gangway walls before we start.

Do you rebuild chimneys or just repoint them?

Both. A chimney with sound brick and worn joints gets repointed and a new crown. One that's leaning, cracked through or losing brick gets taken down to solid masonry, usually at or just below the roofline, and rebuilt. See chimney repair.

Do you work in winter?

Small urgent repairs, yes, under heated enclosures. For a full repoint we'd rather book you for April: winter enclosures add cost and the results are less forgiving.

Free estimate

Get a straight answer about your wall

Name, phone and where the building is. We'll set a time to look and send a written estimate, whether it's spot work or a full repoint.

Rather talk it through? Call us.

We call back within one business day to set up a look at the wall. We use your details only to answer you, and we never sell them.

Call us